產品品牌：F10

產品型號：大理石結晶粉

F10 MarbleCrystallizingPower

This product can be used for crystallizing processing and regular maintenance of various marble. It can make the marble surface bright and shining and can enable the marble surface harder and more wearable. There will be no damage to the stone after long use. It will not influence the air conductivity of the stone and will not change the natural color and luster of the stone.

Directions for use:

1.Surface must be clean and dry. Make sure all waxes ,floor finish or other coating are removed.

2.Mix the crystallizing power with the clear water. In the proportion of 1to 2 to a viscous mixture before applying it to the stone surface.

3.Put a white or red polishing pad under the crystallizing machine.

4.Move the crystallizing machine onto the surface, first move left and right then move up and down. Polish until the floor becomes glossy and lustrous. Each operation covers about 3~5 square meters.

5.After a bright crystallizing surface is seen on the stone surface, scrape the pastry substance to the next operating area with a wipe. Continue to polish by adding only a bit of new crystallizing power. Repeat such polishing till a lot of bubbles are seen on the floor and absorb them with a water sampling machine. Then, add new crystallizing power again and operate by using the foregoing method.

6.Repeat the above method to achieve a more crystalline and shiny effect.

7.Clean the floor with clear water and dry the floor when the entire crystallizing operation is completed.

Warning:

This product is to be used only for floor crystallization.

Have no injure with surroundings environment all to person.

Prohibition againstedibility.

Keep it away from children s reach.

F10大理石結晶粉

本產品適用于各種大理石的結晶處理及日常養護，可以是石材表面光亮、堅硬且有較好的重涂性。長時間使用，保護石材不受損壞，不影響石材的透氣性，不改變石材的天然色澤。

使用說明：

1、確保石材表面的潔凈、干爽。清除地表原有的蠟及污物。

2、使用前將結晶粉與清水以1：2的比例調和。

3、將結晶機安裝上白潔墊。

4、在地表上以先左右后上下的順序移動晶面機，研磨直到地表光亮，每次操作區域3～5平米。

5、石材表面出現結晶，用干凈的布將剩余的物體移至下一個需要工作的區域并加入新的結晶粉，繼續研磨，重復此操作至地面出現大量的泡沫然后用吸水機吸盡。然后加入新的結晶粉重復以上操作。

6、重復以上操作得到更加完美的效果。

7、當整個結晶操作完成之后，用清水沖洗并吸干。

警告：

此產品只用作地表結晶。

對人體及環境沒有危害。

禁止服用

放于兒童接觸不到的地方。